• 30 ml PUR Dispense Head

  • Mã sản phẩm: 1464918
  • Phân loại sản phẩm:
    Nhà sản xuất:
  • This Loctite 30 ml PUR Dispense Head is designed for use with the Loctite 30 ml PUR Controller and Pre Heater. The system is used for dispensing Loctite PUR hotmelt adhesive products at manual or semi-automation workstations, such as in workshops, laboratories, industrial installations and production lines. It is a self-contained dispense system, that can also be integrated with Loctite Benchtop Robots.

    NOTE: One of the following Dispense Needles must be selected and purchased separately:

    18 Gauge 1/2 inch long; IDH 1483249
    19 Gauge 1/2 inch long; IDH 1500889
    20 Gauge 1/2 inch long; IDH 1483250
    21 Gauge 1/2 inch long; IDH 1483262
    23 Gauge 1/2 inch long; IDH 1483264
    25 Gauge 1/2 inch long; IDH 1483265

    Minimum flow rate is 1 mg/sec using a 25 gauge Dispense Needle while the maximum flow rate is 73 mg/sec using a 18 gauge Dispense Needle. These values are for reference only; this is not a specification. Flows were established dispensing Loctite adhesive 3542.

  • Giá bán: Liên hệ
  • Product Description Sheet Operating Manual 2D Dwg File 2D Dxf File 3D Stp File

Đánh giá của bạn: 
 
 
 
 
 
 0điểm /0lượt
Còn lại 0 chiếc

This Loctite 30 ml PUR Dispense Head is designed for use with the Loctite 30 ml PUR Controller and Pre Heater. The system is used for dispensing Loctite PUR hotmelt adhesive products at manual or semi-automation workstations, such as in workshops, laboratories, industrial installations and production lines. It is a self-contained dispense system, that can also be integrated with Loctite Benchtop Robots.
 
NOTE:  One of the following Dispense Needles must be selected and purchased separately:
 
18 Gauge 1/2 inch long; IDH 1483249
19 Gauge 1/2 inch long; IDH 1500889
20 Gauge 1/2 inch long; IDH 1483250
21 Gauge 1/2 inch long; IDH 1483262
23 Gauge 1/2 inch long; IDH 1483264
25 Gauge 1/2 inch long; IDH 1483265
 
Minimum flow rate is 1 mg/sec using a 25 gauge Dispense Needle while the maximum flow rate is 73 mg/sec using a 18 gauge Dispense Needle.  These values are for reference only; this is not a specification.  Flows were established dispensing Loctite adhesive 3542.

 
SD15 Tip Heater for 30 ml PUR Dispense System

SD15 Tip Heater for 30 ml PUR Dispense...

1667509

Giá bán: Liên hệ

SD15 Heat Controller for 30 ml PUR Dispense System

SD15 Heat Controller for 30 ml PUR...

1667508

Giá bán: Liên hệ

Dispense Needle - 19 Gauge 1/2 inch long for 30 ml PUR Dispense Head

Dispense Needle - 19 Gauge 1/2 inch long...

1500889

Giá bán: Liên hệ

Dispense Needle - 25 Gauge 1/2 inch long for 30 ml PUR Dispense Head

Dispense Needle - 25 Gauge 1/2 inch long...

1483265

Giá bán: Liên hệ

Dispense Needle - 23 Gauge 1/2 inch long for 30 ml PUR Dispense Head

Dispense Needle - 23 Gauge 1/2 inch long...

1483264

Giá bán: Liên hệ

Dispense Needle - 21 Gauge 1/2 inch long for 30 ml PUR Dispense Head

Dispense Needle - 21 Gauge 1/2 inch long...

1483262

Giá bán: Liên hệ

 

Danh mục sản phẩm


Các hàng đã đặt

Hỗ trợ trực tuyến

Phòng Kỹ thuật
Phòng kinh doanh
Mr Quân - Linh kiện điện tử
+84963580011
Mr Hanh
Mr Tùng - Máy in, mực in
0964510031

Sản phẩm nổi bật

Thống kê truy cập

  •   Đang truy cập 10
 
  •   Hôm nay 1,612
  •   Tháng hiện tại 32,190
  •   Tổng lượt truy cập 4,598,278