• Benchtop 300 ml Cartridge Pusher

  • Mã sản phẩm: 98022
  • Phân loại sản phẩm:
    Nhà sản xuất:
  • The 98022 Benchtop 300 ml Cartridge Pusher is a designed for dispensing low viscosity product to high extrusion rate pastes. The cartridge pusher mechanically applies pressure to the cartridge plunger using a pneumatically driven ram. The pressure to the ram is set with the 0-60 psi pressure regulator. The regulator pressure should not be used above 50 psi, as the maximum cartridge rating is 60 psi and the ratio on the plunger is 1.1.

    Since there is not high pressure air over the cartridge plunger, there is no opportunity for air ingress into the cartridge. The cartridge cylinder and ram are machined to tight tolerances to minimize the potential for skewing the cartridge plunger. A grease reservoir is included which continually applies a thin film of grease to the plunger shaft. If the cartridge cylinder was contaminated, this would prevent the shaft from being jammed (bonded).

    The cartridge cylinder can be removed for easy maintenance. The ram is brought to the home position for loading and unloading using the switch adjacent to the regulator. There is a low level sensor that is compatible with the Loctite Digital Dispense Controller (item # 97101), or the Loctite Digital Multi-Function Controller (item # 1022006). A valve such as the Poppet Valve (item # 986300) will be required with this unit.

  • Giá bán: Liên hệ
  • Data Sheet User Manual Operational Video Integration with Robot 3D Stp File 2D Dwg File 2D Dxf File

    Spare Parts:

    Item Title
    982644 Fischbach Cartridge Adapter, 1/4 x 18 NPT thread to cartridge end
    984826 Replacement Sleeve Kit
    984832 Fitting Kit, 1/4 inch NPT x 1/4 inch tubing. 10 pack

     

Đánh giá của bạn: 
 
 
 
 
 
 0điểm /0lượt
Còn lại 0 chiếc

The 98022 Benchtop 300 ml Cartridge Pusher is a designed for dispensing low viscosity product to high extrusion rate pastes. The cartridge pusher mechanically applies pressure to the cartridge plunger using a pneumatically driven ram. The pressure to the ram is set with the 0-60 psi pressure regulator. The regulator pressure should not be used above 50 psi, as the maximum cartridge rating is 60 psi and the ratio on the plunger is 1.1.

Since there is not high pressure air over the cartridge plunger, there is no opportunity for air ingress into the cartridge. The cartridge cylinder and ram are machined to tight tolerances to minimize the potential for skewing the cartridge plunger. A grease reservoir is included which continually applies a thin film of grease to the plunger shaft. If the cartridge cylinder was contaminated, this would prevent the shaft from being jammed (bonded).

The cartridge cylinder can be removed for easy maintenance. The ram is brought to the home position for loading and unloading using the switch adjacent to the regulator. There is a low level sensor that is compatible with the Loctite Digital Dispense Controller (item # 97101), or the Loctite Digital Multi-Function Controller (item # 1022006). A valve such as the Poppet Valve (item # 986300) will be required with this unit.

 
300 ml Pneumatic Cartridge Dispensing Retainer

300 ml Pneumatic Cartridge Dispensing...

945900

Giá bán: Liên hệ

Soft Press Handheld Pneumatic Applica

Soft Press Handheld Pneumatic Applica

250052

Giá bán: Liên hệ

HD10 Pneumatic Hand-held 300 ml Cartridge Dispenser

HD10 Pneumatic Hand-held 300 ml...

1714379

Giá bán: Liên hệ

Teroson Multi Press 300 ml Cartridge Spray Gun

Teroson Multi Press 300 ml Cartridge...

142241

Giá bán: Liên hệ

High Pressure Benchtop 300 ml Cartridge Dispenser

High Pressure Benchtop 300 ml Cartridge...

1046901

Giá bán: Liên hệ

 

Danh mục sản phẩm


Các hàng đã đặt

Hỗ trợ trực tuyến

Phòng Kỹ thuật
Phòng kinh doanh
Mr Quân - Linh kiện điện tử
+84963580011
Mr Hanh
Mr Tùng - Máy in, mực in
0964510031

Sản phẩm nổi bật

Thống kê truy cập

  •   Đang truy cập 14
 
  •   Hôm nay 614
  •   Tháng hiện tại 55,632
  •   Tổng lượt truy cập 4,817,344